Heating and Hydronic Systems
Heat loss, pipe diameters, pump selection, project planning of collector, exchanger and terminal systems.
Mechanical Installation · Design and Application
Mechanical Installation Project
Mechanical installation project; It defines the design of heating, cooling, ventilation, water systems and auxiliary installations with relevant calculations. MKA Engineering determines the project, implementation and supervision scope separately for new building and existing facility requests.
Technical Scope
We take the harmony of mechanical systems as a basis.
In mechanical installation project design, space needs, energy use, equipment placements, pipe and duct routes, maintenance access and operational continuity are examined together. Interdisciplinary coordination, accounting data, and field applicability are part of the process.
Cooling and Ventilation
Evaluation of cooling loads, ventilation flow rates, duct and equipment placements.
Plumbing and Pressurization
Domestic water, hot water, circulation, waste water, booster, tank and auxiliary installation systems.
Industrial Auxiliary Lines
Project and field coordination in compressed air, process water, cooling water and steam-condensate lines.
Working Method
From discovery to project, from project to field.
The scope of work is determined by the size of the project and existing system data.
01
Needs and field analysis
Building usage data, process demands and existing installations are examined.
02
System and equipment selection
Capacities, locations and operating conditions are evaluated.
03
Calculation and application project
Drawings are prepared with pipe/channel route, hydraulic and thermal controls.
04
Metering and application
The bill of materials, technical specifications, field coordination and testing requirements are determined.
Offer and Preliminary Evaluation
Information needed to get started
For preliminary technical evaluation, the following data available may be shared:
- Architectural plan, floor heights and purposes of use
- Heating, cooling and ventilation needs of spaces
- Process devices and technical data sheets, if available
- Existing installation information, capacity and routes
Standard and Application
Project criteria
In the selection of accounts and equipment, relevant TS/TS EN, ISO, ASHRAE and national legislation references are taken as basis, depending on the nature of the system.
Each project is evaluated separately according to its own structure and usage conditions.
Create Technical Request →Services by Installation Type
Separate project scope for each mechanical installation system.
Examine the calculations, projects and application details of heating, cooling, air conditioning, plumbing, pumps and industrial auxiliary lines under the relevant heading.
01 / HEATING
Heating Installation
Heat loss, boiler, heat pump, heating pipes and pump selection.
Project and account details →02 / COOLINGCooling Installation
Chiller, cooling load, cold water installation and device coordination.
Project and account details →03 / VENTILATIONIndustrial Ventilation
Fresh air, local suction, fan and duct pressure loss calculation.
Project and account details →04 / AIR CONDITIONINGAir Conditioning and Comfort Systems
VRF/VRV, fan-coil, air handling unit and space comfort criteria.
Project and account details →05 / HYDRONICHydronic Systems
Closed circuit piping, circulation pump, heat exchanger and balance.
Project and account details →06 / SANITARYPlumbing
Clean water, hot water, waste water, rain water and column diagrams.
Project and account details →07 / BOOSTERHydrophore and Pump Systems
Pressurization, critical point calculation, pump group and automation.
Project and account details →08 / WAREHOUSEWater Tank and Level Control
Tank filling, motorized valve, float switch, level sensor and alarm.
Project and account details →09 / COMPRESSED AIRCompressed Air Installation
Compressor, ring lines, pressure loss and air quality.
Project and account details →10 / STEAMSteam and Condensate Installation
Steam distribution, steam trap, line drainage and condensate return.
Project and account details →11 / PROCESSProcess Utility Lines
Process water, cooling water, heat exchanger and production auxiliary lines.
Project and account details →12 / TESTInsulation & Commissioning
Heat/condensation insulation, flushing, testing and hydraulic balancing.
Project and account details →Discovery inputs and engineering deliverables
During the Mechanical Installation Project study, the following information available can be shared at the first meeting. Field detection or additional calculation requirements for missing data are determined separately. Preparation of documents does not automatically guarantee acceptance by the relevant institution or a particular test result.
| Startup entry | Output to be defined in the proposal |
|---|---|
| Architectural drawings, space and process usage | System diagrams and layout plans |
| Working hours and capacity expectations | Capacity, pipe/duct and pump calculations |
| Current device, line and energy source information | Equipment list, quantity survey and delivery file defined in the contract |
Frequently asked questions
How to prepare a proposal for a Mechanical Installation Project?
Architectural drawings, location and process usage are shared along with the facility's district, usage style and desired service. Account, project, application and test items are separated in the written scope.
Will existing drawings be sufficient?
The drawings are compared with the field. If there are revisions, changes in use, and missing equipment information, their impact on the account or project is examined.
What documents are submitted?
System diagrams and layout plans, capacity, pipe/duct and pump calculations and other documents included in the scope of work are delivered. The file format and revision scope are determined at the outset.
Is fixed capacity used for each facility?
No. Usage, system structure and field data are different. Numerical values cannot be applied to all facilities without verifying the relevant calculation and method.
Are implementation and control the same scope?
Project planning, assembly, field inspection and testing tasks are defined separately. The proposal states which party is responsible for which work.
From which regions do you receive requests for exploration?
Requests from Çorlu, Ergene, Kapaklı and Tekirdağ are evaluated from our Çerkezköy center. The time and conditions of the field visit are decided separately.
Discovery and technical proposal request
Share the facility location, current project status and the service you want for the Mechanical Installation Project. Let's clarify the scope of discovery, calculation, application and delivery together.
Related service and region information
In addition to new mechanical installation projects, for the operating conditions of the existing system Mechanical installation periodic control scope you can review. In production facilities, compressor capacity, line route and consumption points are separated separately. compressed air installation project are considered within the scope.